Search result
Front Layout / Middle Layout / Rear Layout / TS/CH
Select the layout setting and audio output terminals for your Height speakers.
Configuration
Set the speaker layout when installing 2 sets (4-channels) or more of Height, Ceiling or Dolby Atmos Enabled speakers.
The layouts that can be selected differ depending on the combinations of “Amp Assign” and floor speaker settings in the menu. (Amp Assignlink, Front/Center/Surround/Surround Backlink)
[4-channel height speakers]
Settings |
AUDIO OUT connectors |
||||
---|---|---|---|---|---|
Height Speakers |
NOTE |
Front Layout |
Rear Layout |
HEIGHT 1 |
HEIGHT 2 |
4 spkrs |
|
Front Height |
Top Middle |
Front Height |
Top Middle |
|
Front Height |
Top Rear |
Front Height |
Top Rear |
|
|
Front Height |
Surround Height |
Front Height |
Surround Height |
|
|
Front Height |
Rear Height |
Front Height |
Rear Height |
|
|
Front Height |
Surround Dolby |
Front Height |
Surround Dolby |
|
|
Front Height |
Back Dolby 1 |
Front Height |
Back Dolby |
|
|
Top Front |
Top Rear |
Top Front |
Top Rear |
|
|
Top Front |
Rear Height |
Top Front |
Rear Height |
|
|
Top Front |
Surround Dolby |
Top Front |
Surround Dolby |
|
|
Top Front |
Back Dolby 1 |
Top Front |
Back Dolby |
|
|
Top Middle |
Rear Height |
Top Middle |
Rear Height |
|
|
Front Dolby |
Top Rear |
Front Dolby |
Top Rear |
|
|
Front Dolby |
Rear Height |
Front Dolby |
Rear Height |
|
|
Front Dolby |
Surround Dolby |
Front Dolby |
Surround Dolby |
|
|
Front Dolby |
Back Dolby 1 |
Front Dolby |
Back Dolby |
[5-channel height speakes]
Settings |
AUDIO OUT connectors |
||||||
---|---|---|---|---|---|---|---|
Height Speakers |
NOTE |
Front Layout |
Rear Layout |
TS/CH |
HEIGHT 1 |
HEIGHT 2 |
SURROUND BACK |
5 spkrs |
|
Front Height |
Surround Height |
Top Surround |
Front Height |
Surround Height |
L: Top Surround |
|
Front Height |
Surround Height |
Center Height |
Front Height |
Surround Height |
R: Center Height |
|
|
Front Height |
Rear Height |
Top Surround |
Front Height |
Rear Height |
L: Top Surround |
|
|
Front Height |
Rear Height |
Center Height |
Front Height |
Rear Height |
R: Center Height |
[6-channel height speakes]
Settings |
AUDIO OUT connectors |
|||||||
---|---|---|---|---|---|---|---|---|
Height Speakers |
NOTE |
Front Layout |
Middle Layout |
Rear Layout |
TS/CH |
HEIGHT 1 |
HEIGHT 2 |
SURROUND BACK |
6 spkrs |
|
Front Height |
Top Middle |
Rear Height |
No |
Front Height |
Rear Height |
Top Middle |
2 |
Front Height |
Surround Height |
Rear Height |
No |
Front Height |
Rear Height |
Surround Height |
|
|
Front Height |
Surround Height |
No |
TS/CH |
Front Height |
Surround Height |
L: Top Surround |
|
|
Front Height |
Surround Dolby |
Rear Height |
No |
Front Height |
Rear Height |
Surround Dolby |
|
|
Front Height |
No |
Rear Height |
TS/CH |
Front Height |
Rear Height |
L: Top Surround |
|
|
Top Front |
Top Middle |
Top Rear |
No |
Top Front |
Top Rear |
Top Middle |
|
|
Top Front |
Surround Dolby |
Top Rear |
No |
Top Front |
Top Rear |
Surround Dolby |
|
|
Front Dolby |
Surround Dolby |
Rear Height |
No |
Front Dolby |
Rear Height |
Surround Dolby |
This can be selected when “Amp Assign” is set to “11.1ch” and “Surround Back” is used in the menu. link
Use 2 sets of Height speakers in the appropriate sound modes for Dolby Atmos, DTS:X or Auro-3D playback.
Use the Front Height and Rear Height speakers for Dolby Atmos playback.
Use the Front Height, Surround Height and Rear Height speakers for DTS:X playback.
Use the Front Height and Surround Height speakers for Auro-3D playback.
Connection
Select the audio output terminal.
Spkr + Pre-out |
Speaker and pre-out outputs are active. |
Pre-out Only: |
Only pre-out terminals are active. Interference to the preamplifier can be reduced by turning off the signal path to the power amplifier. |
When “Amp Assign” is set to “Preamplifier”, the “Connection” setting of all speakers will be fixed as “Pre-out Only”.
When “Amp Assign” is set to “11.1ch” and 11 channels of speakers are used, at least one of the channels assigned to the Front channels, Height 2 or Surround Back must be set to “Pre-out Only”.