Playback

Front Layout / Middle Layout / Rear Layout / TS/CH

Select the layout setting and audio output terminals for your Height speakers.

Configuration

Set the speaker layout when installing 2 sets (4-channels) or more of Height, Ceiling or Dolby Atmos Enabled speakers.

The layouts that can be selected differ depending on the combinations of “Amp Assign” and floor speaker settings in the menu. (Amp Assignlink, Front/Center/Surround/Surround Back/Front Widelink)

[4-channel height speakers]

Settings

AUDIO OUT connectors

Height Speakers

NOTE

Front Layout

Rear Layout

HEIGHT 1

HEIGHT 2

HEIGHT 3/FRONT WIDE

4 spkrs

 

Front Height

Top Middle

Front Height

Top Middle

-

 

Front Height

Top Rear

Front Height

Top Rear

-

 

Front Height

Surround Height

Front Height

Surround Height

-

 

Front Height

Rear Height

Front Height

Rear Height

-

 

Front Height

Surround Dolby

Front Height

Surround Dolby

-

 

Front Height

Back Dolby Flower Mark 1

Front Height

Back Dolby

-

 

Top Front

Top Rear

Top Front

Top Rear

-

 

Top Front

Rear Height

Top Front

Rear Height

-

 

Top Front

Surround Dolby

Top Front

Surround Dolby

-

 

Top Front

Back Dolby Flower Mark 1

Top Front

Back Dolby

-

 

Top Middle

Rear Height

Top Middle

Rear Height

-

 

Front Dolby

Top Rear

Front Dolby

Top Rear

-

 

Front Dolby

Rear Height

Front Dolby

Rear Height

-

 

Front Dolby

Surround Dolby

Front Dolby

Surround Dolby

-

 

Front Dolby

Back Dolby Flower Mark 1

Front Dolby

Back Dolby

-

[5-channel height speakes]

Settings

AUDIO OUT connectors

Height Speakers

NOTE

Front Layout

Rear Layout

TS/CH

HEIGHT 1

HEIGHT 2

HEIGHT 3/FRONT WIDE

5 spkrs

 

Front Height

Surround Height

Top Surround

Front Height

Surround Height

L: Top Surround

 

Front Height

Surround Height

Center Height

Front Height

Surround Height

R: Center Height

 

Front Height

Rear Height

Top Surround

Front Height

Rear Height

L: Top Surround

 

Front Height

Rear Height

Center Height

Front Height

Rear Height

R: Center Height

[6-channel height speakes]

Settings

AUDIO OUT connectors

Height Speakers

NOTE

Front Layout

Middle Layout

Rear Layout

TS/CH

HEIGHT 1

HEIGHT 2

HEIGHT 3/FRONT WIDE

6 spkrs

 

Front Height

Top Middle

Rear Height

No

Front Height

Rear Height

Top Middle

Flower Mark 2

Front Height

Surround Height

Rear Height

No

Front Height

Rear Height

Surround Height

 

Front Height

Surround Height

No

TS/CH

Front Height

Surround Height

L: Top Surround
R: Center Height

 

Front Height

Surround Dolby

Rear Height

No

Front Height

Rear Height

Surround Dolby

 

Front Height

Surround Dolby

Back Dolby Flower Mark 1

No

Front Height

Back Dolby

Surround Dolby

 

Front Height

No

Rear Height

TS/CH

Front Height

Rear Height

L: Top Surround
R: Center Height

 

Top Front

Top Middle

Top Rear

No

Top Front

Top Rear

Top Middle

 

Top Front

Surround Dolby

Top Rear

No

Top Front

Top Rear

Surround Dolby

 

Front Dolby

Top Middle

Back Dolby Flower Mark 1

No

Front Dolby

Back Dolby

Top Middle

 

Front Dolby

Surround Dolby

Rear Height

No

Front Dolby

Rear Height

Surround Dolby

 

Front Dolby

Surround Dolby

Back Dolby Flower Mark 1

No

Front Dolby

Back Dolby

Surround Dolby

This can be selected when using two Surround Back speakers. Set “Surround Back” in the menu to “2 spkrs”. link

Use 2 sets of Height speakers in the appropriate sound modes for Dolby Atmos, DTS:X or AURO-3D playback.
Use the Front Height and Rear Height speakers for Dolby Atmos playback.
Use the Front Height, Surround Height and Rear Height speakers for DTS:X playback.
Use the Front Height and Surround Height speakers for AURO-3D playback.

Connection

Select the audio output terminal.

Spkr + Pre-out
(Default):

Speaker and pre-out outputs are active.

Pre-out Only:

Only pre-out terminals are active. Interference to the preamplifier can be reduced by turning off the signal path to the power amplifier.

When “Amp Assign” is set to “Preamplifier”, the “Connection” setting of all speakers will be fixed as “Pre-out Only”.

When “Amp Assign” is set to “13.1ch” and 13 channels of speakers are used, at least one of the channels assigned to the Front, Height 3 or Front Wide must be set to “Pre-out Only”.

back to top