This sets whether to output as specified in “Dynamic Compression” or output directly without compressing the dynamic range of audio recorded in the disc.


On (Default):	Outputs are given based on enabling the settings made in “Dynamic Compression” and Dialogue normalization function.
Off:	“Dynamic Compression” settings and Dialogue normalization are disabled, and the signals on the disc are output as is.

“Loudness Management” can be set when Dolby Digital, Dolby Digital Plus, Dolby TrueHD and Dolby Atmos signal is input.

Dynamic Compression

Compress dynamic range (difference between loud and soft sounds).


Auto:	Automatic dynamic range compression on/off control according to source.
Low / Medium / High:	These set the compression level.
Off (Default):	Dynamic range compression is always off.

“Dynamic Compression” can be set when Dolby Digital, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos or DTS signal is input.

“Auto” cannot be set when inputting a DTS signal.

Dialog Control

Adjust the volume of dialog in movies, vocals in music, etc. so these can be heard more easily.


0 – 6 (Default : 0)

This can be set when a DTS:X signal that is compatible with the Dialog Control function is input.

Low Frequency Effects

Adjust the low frequency effects level (LFE).


-10 dB – 0 dB (Default: 0 dB)

This can be set when the LFE signal is included in the input signal.

This item can be selected when a Dolby Digital or DTS signal or DVD-Audio is played.

For proper playback of the different sources, we recommend setting to the values below.

Dolby Digital sources: 0 dB

DTS movie sources: 0 dB

DTS music sources: -10 dB

Speaker Virtualizer

The Speaker Virtualizer enhances the surround and height speaker channels to create an enveloping virtual surround effect.


On (Default):	Enables “Speaker Virtualizer”.
Off:	Disables “Speaker Virtualizer”.

You can set this when the sound mode is “Dolby Atmos”, “Dolby Surround” or sound mode that has “+Dolby Surround” in the sound mode name.

Usable when not using height, ceiling or Dolby Atmos Enabled speakers, or when not using surround speakers.

Audio is not output from the surround back speaker if “Speaker Virtualizer” is set to “On” when “Speaker Layout” - “Surround Back” is set to “1 spkr” in the menu.

Center Spread

Center Spread expands the center channel signal to left and right front speakers to create a wider frontal audio image for the listener. It is optimized and designed primary for playback of stereo music content.


On:	Use “Center Spread”.
Off (Default):	Do not use “Center Spread”.

You can set this when sound mode is “Dolby Surround”.

DTS Neural:X

DTS Neural:X Expands the non-object based audio signals and optimizes them for your speaker configuration.


On (Default):	Use “DTS Neural:X”.
Off:	Do not use “DTS Neural:X”.

You can set this when sound mode is “DTS:X”.

IMAX

Sets the audio mode for IMAX playback.


Auto (Default):	Automatically enables IMAX mode when IMAX content is detected.
Off:	Disables IMAX mode.

This setting cannot be set when headphones are used.

IMAX Audio Settings

You can configure special IMAX audio settings to recreate the conditions of an IMAX theater.


Auto (Default):	Applies the optimized speaker settings to reproduce similar to the IMAX theater environment.
Manual:	Manually adjusts the “High Pass Filter”, “Low Pass Filter” and “Subwoofer Output”.

You can set this when sound mode is “IMAX DTS” or “IMAX DTS:X”.

“Speakers” - “Crossovers”, “Bass” - “Subwoofer Output” and “LPF for LFE” in the menu cannot be applied during IMAX playback.

High Pass Filter

Set the high pass filter cutoff frequency for all speakers during IMAX playback.


40 Hz / 60 Hz / 80 Hz / 90 Hz / 100 Hz / 110 Hz / 120 Hz / 150 Hz / 180 Hz / 200 Hz / 250 Hz (Default: 80 Hz)

You can set this when “IMAX Audio Settings” is set to “Manual”.

Low Pass Filter

Set the low pass filter cutoff frequency of the LFE signal during IMAX playback.


80 Hz / 90 Hz / 100 Hz / 110 Hz / 120 Hz / 150 Hz / 180 Hz / 200 Hz / 250 Hz (Default: 120 Hz)

You can set this when “IMAX Audio Settings” is set to “Manual”.

Subwoofer Output

Set the bass signal to be played by the subwoofer during IMAX playback.


LFE + Main:	The low range signal of all speakers is added to the LFE signal output from the subwoofer. The LFE signal and the bass component of each speaker is played.
LFE (Default):	Only the LFE signal is played.

You can set this when “IMAX Audio Settings” is set to “Manual”.

Auro-Matic Preset

Selects the Auro-Matic Preset for fine tuning the AURO-3D experience to specific audio material.


Small:	“Small” is ideal for pop and chamber music.
Medium (Default):	“Medium” is ideal on jazz music or typical movies and TV shows.
Large:	“Large” is ideal for recordings that were recorded in large spaces (e.g. orchestral recording).
Movie:	“Movie” is ideal for experiencing a large-cinema effect for watching movies (e.g. action movies with big explosions).
Speech:	“Speech” is ideal for recordings which are mostly dialog (e.g. news broadcast), and that have virtually no inherent spatial information.

You can set this when the sound mode is set to “AURO-3D” or “AURO Surround”.

This cannot be set if the input signal contains AURO-3D signals containing a Height channel.

Auro-Matic Strength

Changes the level of the up-mixed channels in relation to the original input signal.
The value ranges from 0 (no up-mixing) to 15 (Maximum level, providing maximum effect).


0 - 15 (Default:12)

You can set this when the sound mode is set to “AURO-3D” or “AURO Surround”.

This cannot be set if the input signal contains AURO-3D signals containing a Height channel.

AURO-3D Mode

Select how to output sound to all speakers when AURO-3D decoding is active.


Channel Expansion (Default):	Incoming AURO-3D content is expanded to additional speakers. All speakers configured for AURO-3D will output sound.
Direct:	Incoming AURO-3D content is sent directly to each corresponding channel. No content is sent to additional speakers.

You can set this when the input signal contains AURO-3D signal and sound mode is set to AURO-3D.

Speaker Select

Selects which speakers output sound, depending on the current sound mode.


Floor:	Plays back without height speakers.
Floor & Height (Default):	Plays back with height speakers.

This can be set when the sound mode is the Multi Ch Stereo mode.

Subwoofer

Turn subwoofer output on and off.


On (Default):	The subwoofer is used.
Off:	The subwoofer is not used.

You can set this when the sound mode is “Direct” or “Stereo” and in the menu “Subwoofer Output” is set to “LFE + Main”. link

Set Defaults

The “Surround Parameter” settings are returned to the default settings.