Search result
Specifications
Audio section
Power amplifier
Rated output: |
Front: |
110 W + 110 W (8 Ω/ohms, 20 Hz – 20 kHz with 0.08 % T.H.D.) |
|
150 W + 150 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.) |
|
Center: |
|
110 W (8 Ω/ohms, 20 Hz – 20 kHz with 0.08 % T.H.D.) |
|
150 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.) |
|
Surround: |
|
110 W + 110 W (8 Ω/ohms, 20 Hz – 20 kHz with 0.08 % T.H.D.) |
|
150 W + 150 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.) |
|
Surround back / Height1 / Height2: |
|
110 W + 110 W (8 Ω/ohms, 20 Hz – 20 kHz with 0.08 % T.H.D.) |
|
150 W + 150 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.) |
|
Output connectors: |
4 – 16 Ω/ohms |
Analog
Input sensitivity: |
200 mV |
Frequency response: |
10 Hz – 100 kHz — +1, –3 dB (Direct mode) |
S/N: |
100 dB (IHF–A weighted, Direct mode) |
Distortion: |
0.005 % (20 Hz – 20 kHz) (Direct mode) |
Rated output: |
1.2 V |
Digital
D/A output: |
Rated output — 2 V (at 0 dB playback) |
Total harmonic distortion — 0.008 % (1 kHz, at 0 dB) |
|
S/N ratio — 102 dB |
|
Dynamic range — 100 dB |
|
Digital input: |
Format — Digital audio interface |
Phono equalizer
Input sensitivity: |
2.5 mV |
RIAA deviation: |
±1 dB (20 Hz to 20 kHz) |
S/N: |
74 dB (IHF-A) |
Distortion factor: |
0.03 % (1 kHz, 3 V) |
Video section
Standard video connectors
Input/output level and impedance: |
1 Vp-p, 75 Ω/ohms |
Frequency response: |
5 Hz – 10 MHz — 0, –3 dB |
Color component video connector
Input/output level and impedance: |
Y signal — 1 Vp-p, 75 Ω/ohms PB / CB signal — 0.7 Vp-p, 75 Ω/ohms PR / CR signal — 0.7 Vp-p, 75 Ω/ohms |
Frequency response: |
5 Hz – 60 MHz — 0, –3 dB |
Tuner section |
[FM] |
[AM] |
|
(Note: μV at 75 Ω/ohms, 0 dBf = 1 x 10 –15 W) |
|
Reception frequency range: |
87.5 MHz – 107.9 MHz |
520 kHz – 1710 kHz |
Effective sensitivity: |
1.2 μV (12.8 dBf) |
18 μV |
50 dB sensitivity: |
MONO ― 2.8 μV (20.2 dBf) |
|
S/N ratio: |
MONO ― 70 dB (IHF–A weighted, Direct mode) STEREO ― 67 dB (IHF–A weighted, Direct mode) |
|
Distortion: |
MONO ― 0.7 % (1 kHz) STEREO ― 1.0 % (1 kHz) |
Wireless LAN section
Network type (wireless LAN standard): |
Conforming to IEEE 802.11a |
Security: |
WEP 64 bit, WEP 128 bit |
WPA/WPA2-PSK (AES) |
|
WPA/WPA2-PSK (TKIP) |
|
Radio frequency: |
2.4 GHz, 5 GHz |
No. of channels: |
2.4 GHz: 1 – 11ch |
The Wi-Fi® CERTIFIED Logo and the Wi-Fi CERTIFIED On-Product Logo are registered trademarks of the Wi-Fi Alliance.
Bluetooth section
Communications system: |
Bluetooth Version 2.1 + EDR (Enhanced Data Rate) |
Transmission power: |
Maximum 2.5 mW (Class 2) |
Maximum communication range: |
Approx. 32.8 ft/10 m in line of sight ∗2 |
Frequency band: |
2.4 GHz band |
Modulation scheme: |
FHSS (Frequency-Hopping Spread Spectrum) |
Supported profiles: |
A2DP (Advanced Audio Distribution Profile) 1.2 |
AVRCP (Audio Video Remote Control Profile) 1.4 |
|
Corresponding codec: |
SBC, AAC |
Transmission range (A2DP): |
20 Hz – 20,000 Hz |
The actual communication range varies depending on the influence of such factors as obstructions between devices, electromagnetic waves from microwave ovens, static electricity, cordless phones, reception sensitivity, antenna performance, operating system, application software etc.
General
Power supply: |
AC 120 V, 60 Hz |
Power consumption: |
680 W |
Power consumption in standby mode: |
0.2 W |
Power consumption in CEC standby mode: |
0.5 W |
Power consumption in network standby mode: |
2.7 W |
For purposes of improvement, specifications and design are subject to change without notice.