Search result
Registering preset codes
There are two methods for registering preset codes; the simple method for registering preset codes of Marantz players, the method for registering the preset numbers of other manufacturers’ devices, and the method for experimenting with preset codes one by one for registration.
Registering Marantz players
Use the following simple method to register the preset codes of Marantz Blu-ray Disc players, DVD players and CD players.
Registering Blu-ray Disc players
Press and hold down Blu-ray and OPTION until “OK” indicator on the remote control display is flashing, then release.
Registering DVD players
Press and hold down DVD and OPTION until “OK” indicator on the remote control display is flashing, then release.
Registering CD players
Press and hold down CD and OPTION until “OK” indicator on the remote control display is flashing, then release.
Registering multiple players at the same time
Press and hold down the SMART SELECT 1 – 4 and OPTION until “OK” indicator on the remote control display is flashing, then release.
|
Devices to be registered at the same time |
Press and hold down the buttons |
||
|---|---|---|---|
|
Blu-ray Disc player |
DVD player |
CD player |
|
|
|
|
|
SMART SELECT 1 and OPTION |
|
|
|
|
SMART SELECT 2 and OPTION |
|
|
|
|
SMART SELECT 3 and OPTION |
|
|
|
|
SMART SELECT 4 and OPTION |
NOTE
Depending on the model and year of manufacture of your device, some buttons may not operate. In this case, try “Registering by entering preset numbers” link.
Registering by entering preset numbers
The following table shows the device groups that can be registered for each of the input source select buttons. Check the preset number of the device you want to register beforehand in the “Remote Control Preset Codes” file.
|
Button |
Device groups that can be registered |
|---|---|
|
|
CBL/SAT group |
|
|
BD/DVD group |
|
|
CBL/SAT group, BD/DVD group, |
|
|
CBL/SAT group |
|
|
BD/DVD group |
|
|
CBL/SAT group, BD/DVD group, |
|
|
CBL/SAT group, BD/DVD group, |
|
|
Audio group |
|
|
TV group |
Press and hold down the input source select button that you want to register the preset code to and SET until “PRSET” indicator on the remote control display is flashing, then release.
Enter the preset number (4 digits) listed for the device in the Preset Code Table using the number buttons (0 – 9) on the remote control.
Some manufacturers use more than one type of remote control code. Preset codes to change the number and verify correct operation.
If the unit does not operate even when the preset code is registered, use the learning function. Remote codes for different devices can be remembered for use by the Marantz remote control included with this unit. link
NOTE
Depending on the model and year of manufacture of your device, some buttons may not operate.
Experimenting with preset codes one by one for registration
Switch the power on of the device for which you want to set the preset code.
Press and hold down the input source select button that you want to register the preset code to and SET until “PRSET” indicator on the remote control display is flashing, then release.
Aim the remote control at the appliance and slowly alternate between pressing CH/PAGE 
and DEVICE 
for the appliance.
and DEVICE for the appliance.The preset code is shown in the remote control display.
Stop when the appliance turns off.
Press ENTER once to lock in the code.
Some manufacturers use more than one type of remote control code. Preset codes to change the number and verify correct operation.
If the unit does not operate even when the preset code is registered, use the learning function. Remote codes for different devices can be remembered for use by the Marantz remote control included with this unit. link
NOTE
Depending on the model and year of manufacture of your device, some buttons may not operate.