You need to configure the detailed settings for the speaker configuration in accordance with the selected mode. Select Assign Mode configure the corresponding detailed settings.


9.1ch :	Setting to use the 7-channel power amplifier within this unit and an external power amplifier connected to PRE OUT connector to play back up to 9.1-channels. You can connect speakers for up to 13.1-channels for MAIN ZONE. Speakers to output audio are automatically switched for playing back up to 9.1-channels in accordance with the input signal and sound mode.
7.1ch (Default):	Settings to assign all power amplifier within this unit to MAIN ZONE to play back up to 7.1-channels. You can connect speakers for up to 11.1-channels for MAIN ZONE. Speakers to output audio are automatically switched for playing back up to 7.1-channels in accordance with the input signal and sound mode.


5.1ch + ZONE2:	Setting to assign the power amplifiers in this unit for ZONE2 to 2-channels.
5.1ch (Bi-Amp) :	Setting to assign the power amplifiers in this unit for front speaker bi-amp connection to 2-channels.
7.1ch/2ch Front :	Setting to assign the power amplifiers in this unit for connecting 2-channel playback speakers to 2-channels. You can switch the front speakers when using 2-channel playback in direct mode or stereo mode, or when using multi-channel surround playback.
5.1ch + Front B :	Setting to assign the power amplifiers within this unit for connecting the second set of front speakers. You can switch between the desired combination of front speakers A and front speakers B. Switch the front speaker using the “Front Speaker” setting. link

Floor

Layout

Select the floor speakers location.


5ch & SB & FW∗1：	This layout combines a surround back or front wide speaker with the basic 5-channel layout.
5ch & SB∗2 (Default)：	This layout combines a surround back speaker with the basic 5-channel layout.
5ch & FW∗1：	This layout combines a front wide speaker with the basic 5-channel layout.
5ch∗2：	This is a basic 5-channel layout that uses front speakers, center speakers and surround speakers.

This can be selected when “Assign Mode” is set to “9.1ch” or “7.1ch” in the menu. link

This can be selected when “Assign Mode” is set to “9.1ch”, “7.1ch” or “7.1ch/2ch Front” in the menu. link

Height

Height Sp

Select the number of the height speakers and ceiling speakers used in MAIN ZONE.


None：	Uses no height and ceiling speakers.
2ch (Default)：	Uses a set of (two) height speakers or ceiling speakers.
4ch：	Uses two sets of (four) height speakers or ceiling speakers.

Dolby Sp

Select the number of the Dolby Atmos Enabled speakers used in MAIN ZONE.


None (Default)：	Uses no Dolby Atmos Enabled speakers.
2ch：	Uses a set of (two) Dolby Atmos Enabled speakers.
4ch：	Uses two sets of (four) Dolby Atmos Enabled speakers.

Layout

Select the height, ceiling, or Dolby Atmos Enabled speaker location.

The layouts that can be selected differ depending on the combinations of “Assign Mode” and “Floor” - “Layout” in the menu. (Assign Modelink, “Floor” - Layoutlink)

Settings				AUDIO OUT connectors
Height Speakers	Dolby Speakers	NOTE	Layout	HEIGHT1	HEIGHT2
None	None		-	-	-
2ch	None		Front Height (Default)	Front Height	-
			Top Front	Top Front	-
			Top Middle	Top Middle	-
			Top Rear	Top Rear	-
			Rear Height	Rear Height	-
4ch	None	1	Front Height & Top Middle	Front Height	Top Middle
			Front Height & Top Rear	Front Height	Top Rear
			Front Height & Rear Height	Front Height	Rear Height
			Top Front & Top Rear	Top Front	Top Rear
			Top Front & Rear Height	Top Front	Rear Height
			Top Middle & Rear Height	Top Middle	Rear Height
None	2ch		Front Dolby	Front Dolby	-
			Surround Dolby	Surround Dolby	-
			Back Dolby 2	Back Dolby	-

This can be selected when “Assign Mode” is set to “9.1ch” in the menu.

This can be selected when “Assign Mode” is set to “9.1ch” and “Floor” - “Layout” is set to “5ch & SB & FW” or “5ch & SB” in the menu.

Settings				AUDIO OUT connectors
Height Speakers	Dolby Speakers	NOTE	Layout	HEIGHT1	HEIGHT2
2ch	2ch	1	Front Dolby & Top Rear	Front Dolby	Top Rear
			Front Dolby & Rear Height	Front Dolby	Rear Height
			Front Height & Surr. Dolby	Front Height	Surround Dolby
			Top Front & Surround Dolby	Top Front	Surround Dolby
None	4ch	1	Front Dolby & Surround Dolby	Front Dolby	Surround Dolby
			Front Dolby & Back Dolby 3	Front Dolby	Back Dolby

This can be selected when “Assign Mode” is set to “9.1ch” in the menu.

Pre-out

When “Assign Mode” is set to “9.1ch”, selects the PRE OUT connect the external power amplifier used in MAIN ZONE.

The PRE OUT connectors that can be selected differ depending on the combination of “Floor” - “Layout” and “Height” - “Layout” settings configured in the menu.


Surr. Back (Default)：	The surround back left and right pre-amp outputs are connected to an external amplifier.
Front Wide:	The front wide left and right pre-amp outputs are connected to an external amplifier.
Front:	The front left and right pre-amp outputs are connected to an external amplifier.
HEIGHT1 ∗1:	The HEIGHT1 left and right pre-amp outputs are connected to an external amplifier.
HEIGHT2 ∗2:	The HEIGHT2 left and right pre-amp outputs are connected to an external amplifier.
Surround Back & HEIGHT2 ∗2:	The surround back/HEIGHT2 left and right pre-amp outputs are connected to an external amplifier.
Front Wide & HEIGHT2 ∗2:	The front wide/HEIGHT2 left and right pre-amp outputs are connected to an external amplifier.
HEIGHT1 & HEIGHT2 ∗1∗2:	The HEIGHT1/HEIGHT2 left and right pre-amp outputs are connected to an external amplifier.
Front & HEIGHT2 ∗2:	The front/HEIGHT2 left and right pre-amp outputs are connected to an external amplifier.
Front & Front Wide :	The front/front wide left and right pre-amp outputs are connected to an external amplifier.