Search result
Amp Assign
You can change the Pre Amplifier assignment according to your speaker system.
Assign Mode
Select how to use the Pre Amplifier.
You need to configure the detailed settings for the speaker configuration in accordance with the selected mode. Select Assign Mode configure the corresponding detailed settings.
11.1ch |
All Pre Amplifiers of this unit are used for MAIN ZONE. |
9.1ch (Bi-Amp): |
The Pre Amplifier of this unit is assigned to 2-channels for creating bi-amp connections with the front speaker. You can connect speakers for up to 9.1-channels for MAIN ZONE. |
9.1ch + Front B: |
The Pre Amplifier of this unit is assigned to 2-channels for connecting to the second front speaker. You can connect speakers for up to 9.1-channels for MAIN ZONE. |
Pre-out for Bi-Amp / Pre-out for Front B
When “Assign Mode” is set to “9.1ch (Bi-Amp)” or “9.1ch + Front B” in the menu, select the PRE OUT connectors used for bi-amp or second pair front speakers.
HEIGHT 2 |
The assigned channels are output from the HEIGHT2 PRE OUT connectors. Up to one pair of height, ceiling, and Dolby Atmos Enabled channels can be used. |
SURROUND BACK: |
The assigned channels are output from the SURROUND BACK PRE OUT connectors. The surround back channel cannot be used. |
Floor
Select the floor speakers location.
5ch & SB |
This layout combines a surround back speaker with the basic 5-channel layout. |
5ch: |
This is a basic 5-channel layout that uses front speakers, center speakers and surround speakers. |
Height
Height Sp
Select the number of the height speakers and ceiling speakers used in MAIN ZONE.
None: |
Uses no height and ceiling speakers. |
2ch: |
Uses a set of (two) height speakers or ceiling speakers. |
4ch |
Uses two sets of (four) height speakers or ceiling speakers. |
5ch: |
Uses five height speakers ∗ |
If “5ch” is selected, connect the Top Surround speaker to the SUBWOOFER 2 connector.
Dolby Sp
Select the number of the Dolby Atmos Enabled speakers used in MAIN ZONE.
None |
Uses no Dolby Atmos Enabled speakers. |
2ch: |
Uses a set of (two) Dolby Atmos Enabled speakers. |
4ch: |
Uses two sets of (four) Dolby Atmos Enabled speakers. |
Layout
Select the height, ceiling, or Dolby Atmos Enabled speaker location.
The layouts that can be selected differ depending on the combinations of “Assign Mode” and “Floor” in the menu. (Assign Modelink, Floorlink)
Settings |
AUDIO OUT connectors |
||||
---|---|---|---|---|---|
Height Sp |
Dolby Sp |
NOTE |
Layout |
HEIGHT 1 |
HEIGHT 2 |
None |
None |
|
- |
- |
- |
2ch |
None |
|
Front Height |
Front Height |
- |
Top Front |
Top Front |
- |
|||
Top Middle |
Top Middle |
- |
|||
Top Rear |
Top Rear |
- |
|||
Rear Height |
Rear Height |
- |
|||
4ch |
None |
1 |
Front Height & Top Middle |
Front Height |
Top Middle |
Front Height & Top Rear |
Front Height |
Top Rear |
|||
Front Height & Rear Height 2 |
Front Height |
Rear Height |
|||
Front Height & Surr. Height |
Front Height |
Surr. Height |
|||
Top Front & Top Rear (Default) |
Top Front |
Top Rear |
|||
Top Front & Rear Height |
Top Front |
Rear Height |
|||
Top Middle & Rear Height |
Top Middle |
Rear Height |
|||
None |
2ch |
|
Front Dolby |
Front Dolby |
- |
Surround Dolby |
Surround Dolby |
- |
|||
Back Dolby 3 |
Back Dolby |
- |
This can be selected when “Assign Mode” is set to “11.1ch”, when “Assign Mode” is set to “9.1ch (Bi-Amp)” and “Pre-out for Bi-Amp” is set to “SURROUND BACK” or when “Assign Mode” is set to “9.1ch + Front B” and “Pre-out for Front B” is set to “SURROUND BACK” in the menu.
For the best Auro-3D experience Surround Height speakers are recommended, however you may substitute Rear Height speakers from a Dolby Atmos speaker setup in place of Surround Height speakers.
This can be selected when “Floor” is set to “5ch & SB” in the menu.
Settings |
AUDIO OUT connectors |
||||
---|---|---|---|---|---|
Height Sp |
Dolby Sp |
NOTE |
Layout |
HEIGHT 1 |
HEIGHT 2 |
2ch |
2ch |
1 |
Front Dolby & Top Rear |
Front Dolby |
Top Rear |
Front Dolby & Rear Height |
Front Dolby |
Rear Height |
|||
Front Height & Surr. Dolby |
Front Height |
Surround Dolby |
|||
Front Height & Back Dolby 4 |
Front Height |
Back Dolby |
|||
Top Front & Surr. Dolby |
Top Front |
Surround Dolby |
|||
Top Front & Back Dolby 4 |
Top Front |
Back Dolby |
|||
None |
4ch |
1 |
Front Dolby & Surr. Dolby |
Front Dolby |
Surround Dolby |
Front Dolby & Back Dolby 4 |
Front Dolby |
Back Dolby |
This can be selected when “Assign Mode” is set to “11.1ch”, when “Assign Mode” is set to “9.1ch (Bi-Amp)” and “Pre-out for Bi-Amp” is set to “SURROUND BACK” or when “Assign Mode” is set to “9.1ch + Front B” and “Pre-out for Front B” is set to “SURROUND BACK” in the menu.
This can be selected when “Assign Mode” is set to “11.1ch” and “Floor” is set to “5ch & SB” in the menu.
Settings |
AUDIO OUT connectors |
|||||
---|---|---|---|---|---|---|
Height Sp |
Dolby Sp |
NOTE |
Layout |
HEIGHT1 |
HEIGHT2 |
SUBWOOFER2 |
5ch |
None |
5 |
Front Height & Surr. Height |
Front Height |
Surr. Height |
Top Surround |
Front Height & Rear Height 2 |
Front Height |
Rear Height |
Top Surround |
For the best Auro-3D experience Surround Height speakers are recommended, however you may substitute Rear Height speakers from a Dolby Atmos speaker setup in place of Surround Height speakers.
This can be selected when “Assign Mode” is set to “11.1ch” in the menu.
View Terminal Config.
This shows how to connect the PRE OUT connectors for your “Amp Assign” setting on the menu screen.