Search result
Specifications
Audio section
Power amplifier
|
Rated output: |
Front: |
|
110 W + 110 W (8 Ω/ohms, 20 Hz – 20 kHz with 0.08 % T.H.D.) |
|
|
150 W + 150 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.) |
|
|
Center: |
|
|
110 W (8 Ω/ohms, 20 Hz – 20 kHz with 0.08 % T.H.D.) |
|
|
150 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.) |
|
|
Surround: |
|
|
110 W + 110 W (8 Ω/ohms, 20 Hz – 20 kHz with 0.08 % T.H.D.) |
|
|
150 W + 150 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.) |
|
|
Surround back / Height1 / Height2: |
|
|
110 W + 110 W (8 Ω/ohms, 20 Hz – 20 kHz with 0.08 % T.H.D.) |
|
|
150 W + 150 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.) |
|
|
Output connectors: |
4 – 16 Ω/ohms |
Analog
|
Input sensitivity: |
200 mV |
|
Frequency response: |
10 Hz – 100 kHz — +1, –3 dB (Direct mode) |
|
S/N: |
100 dB (IHF–A weighted, Direct mode) |
|
Distortion: |
0.005 % (20 Hz – 20 kHz) (Direct mode) |
|
Rated output: |
1.2 V |
Digital
|
D/A output: |
Rated output — 2 V (at 0 dB playback) |
|
Total harmonic distortion — 0.008 % (1 kHz, at 0 dB) |
|
|
S/N ratio — 102 dB |
|
|
Dynamic range — 100 dB |
|
|
Digital input: |
Format — Digital audio interface |
Phono equalizer
|
Input sensitivity: |
2.5 mV |
|
RIAA deviation: |
±1 dB (20 Hz to 20 kHz) |
|
S/N: |
74 dB (IHF-A) |
|
Distortion factor: |
0.03 % (1 kHz, 3 V) |
Video section
Standard video connectors
|
Input/output level and impedance: |
1 Vp-p, 75 Ω/ohms |
|
Frequency response: |
5 Hz – 10 MHz — 0, –3 dB |
Color component video connector
|
Input/output level and impedance: |
Y signal — 1 Vp-p, 75 Ω/ohms PB / CB signal — 0.7 Vp-p, 75 Ω/ohms PR / CR signal — 0.7 Vp-p, 75 Ω/ohms |
|
Frequency response: |
5 Hz – 60 MHz — 0, –3 dB |
Wireless LAN section
|
Network type (wireless LAN standard): |
Conforming to IEEE 802.11a/b/g/n |
|
Security: |
WEP 64 bit, WEP 128 bit |
|
WPA/WPA2-PSK (AES) |
|
|
WPA/WPA2-PSK (TKIP) |
|
|
Used frequency range: |
2.4 GHz, 5 GHz |
The Wi-Fi® CERTIFIED Logo and the Wi-Fi CERTIFIED On-Product Logo are registered trademarks of the Wi-Fi Alliance.
Bluetooth section
|
Communications system: |
Bluetooth Specification Version 4.2 |
|
Transmission power: |
Bluetooth Specification Power Class 1 |
|
Maximum communication range: |
Approx. 30 m in line of sight ∗2 |
|
Used frequency range: |
2.4 GHz |
|
Modulation scheme: |
FHSS (Frequency-Hopping Spread Spectrum) |
|
Supported profiles: |
Receiver function A2DP (Advanced Audio Distribution Profile) 1.2 |
|
AVRCP (Audio Video Remote Control Profile) 1.5 Transmitter function A2DP (Advanced Audio Distribution Profile) 1.2 |
|
|
Corresponding codec: |
SBC |
|
Transmission range (A2DP): |
20 Hz – 20,000 Hz |
The actual communication range varies depending on the influence of such factors as obstructions between devices, electromagnetic waves from microwave ovens, static electricity, cordless phones, reception sensitivity, antenna performance, operating system, application software etc.
General
|
Operating temperature: |
5 °C - 35 °C |
|
Power supply: |
AC 230 V, 50/60 Hz |
|
Power consumption: |
680 W |
|
Power consumption in standby modes: |
|
|
Standby modes |
Setting items in the menu |
Power consumption |
||
|---|---|---|---|---|
|
Network Control |
Allow Update |
|||
|
Normal standby |
Off In Standby |
Off |
Off |
0.2 W |
|
Network control (Bluetooth) |
Always On |
– |
Off |
3.3 W |
|
Network control (Ethernet) |
Always On |
– |
Off |
3.4 W |
|
Network control (Wi-Fi) |
Always On |
– |
Off |
3.7 W |
|
CEC standby |
Off In Standby |
Off |
On |
0.5 W |
|
RS-232C standby ∗ |
Off In Standby |
Off |
Off |
0.5 W |
When this unit is in standby mode by sending a standby command from the external controller via the RS-232C connector of this unit.
For purposes of improvement, specifications and design are subject to change without notice.