Search result
Specifications
Audio section
Power amplifier
|
Rated output: |
Front: |
|
100 W + 100 W (8 Ω/ohms, 20 Hz – 20 kHz with 0.08 % T.H.D.) |
|
|
140 W + 140 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.) |
|
|
Center: |
|
|
100 W (8 Ω/ohms, 20 Hz – 20 kHz with 0.08 % T.H.D.) |
|
|
140 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.) |
|
|
Surround: |
|
|
100 W + 100 W (8 Ω/ohms, 20 Hz – 20 kHz with 0.08 % T.H.D.) |
|
|
140 W + 140 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.) |
|
|
Surround back: |
|
|
100 W + 100 W (8 Ω/ohms, 20 Hz – 20 kHz with 0.08 % T.H.D.) |
|
|
140 W + 140 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.) |
|
|
Output connectors: |
4 – 16 Ω/ohms |
Analog
|
Input sensitivity: |
200 mV |
|
Frequency response: |
10 Hz – 100 kHz — +1, –3 dB (Direct mode) |
|
S/N: |
100 dB (IHF–A weighted, Direct mode) |
Video section
Standard video connectors
|
Input/output level and impedance: |
1 Vp-p, 75 Ω/ohms |
|
Frequency response: |
5 Hz – 10 MHz — 0, –3 dB |
Color component video connector
|
Input/output level and impedance: |
Y signal — 1 Vp-p, 75 Ω/ohms PB / CB signal — 0.7 Vp-p, 75 Ω/ohms PR / CR signal — 0.7 Vp-p, 75 Ω/ohms |
|
Frequency response: |
5 Hz – 60 MHz — 0, –3 dB |
Tuner section |
[FM] |
[AM] |
|
|
(Note: μV at 75 Ω/ohms, 0 dBf = 1 x 10 –15 W) |
|
|
Reception frequency range: |
87.5 MHz – 107.9 MHz |
520 kHz – 1710 kHz |
|
Effective sensitivity: |
1.2 μV (12.8 dBf) |
18 μV |
|
50 dB sensitivity: |
MONO ― 2.8 μV (20.2 dBf) |
|
|
S/N ratio: |
MONO ― 70 dB (IHF–A weighted, Direct mode) STEREO ― 67 dB (IHF–A weighted, Direct mode) |
|
|
Distortion: |
MONO ― 0.7 % (1 kHz) STEREO ― 1.0 % (1 kHz) |
Wireless LAN section
|
Network type (wireless LAN standard): |
Conforming to IEEE 802.11a/b/g/n |
|
Security: |
WEP 64 bit, WEP 128 bit |
|
WPA/WPA2-PSK (AES) |
|
|
WPA/WPA2-PSK (TKIP) |
|
|
Used frequency range: |
2.4 GHz, 5 GHz |
The Wi-Fi® CERTIFIED Logo and the Wi-Fi CERTIFIED On-Product Logo are registered trademarks of the Wi-Fi Alliance.
Bluetooth section
|
Communications system: |
Bluetooth Specification Version 3.0 + EDR (Enhanced Data Rate) |
|
Transmission power: |
Bluetooth Specification Power Class 1 |
|
Maximum communication range: |
Approx. 98.4 ft/30 m in line of sight ∗2 |
|
Used frequency range: |
2.4 GHz |
|
Modulation scheme: |
FHSS (Frequency-Hopping Spread Spectrum) |
|
Supported profiles: |
A2DP (Advanced Audio Distribution Profile) 1.2 |
|
AVRCP (Audio Video Remote Control Profile) 1.5 |
|
|
Corresponding codec: |
SBC |
|
Transmission range (A2DP): |
20 Hz – 20,000 Hz |
The actual communication range varies depending on the influence of such factors as obstructions between devices, electromagnetic waves from microwave ovens, static electricity, cordless phones, reception sensitivity, antenna performance, operating system, application software etc.
General
|
Power supply: |
AC 120 V, 60 Hz |
|
Power consumption: |
650 W |
|
Power consumption in standby mode: |
0.2 W ∗ |
|
Power consumption in CEC standby mode: |
0.5 W |
When “Network Control” in the menu is set to “Off In Standby” and “HDMI Pass Through” is set to “Off”.
For purposes of improvement, specifications and design are subject to change without notice.