Specifications

Audio section

Analog

Input sensitivity:

Unbalanced RCA input : 200 mV
Balanced XLR input : 400 mV

Frequency response:

10 Hz – 100 kHz — +1, –3 dB (Direct mode)

S/N:

105 dB (IHF–A weighted, Direct mode)

Distortion:

0.005 % (20 Hz – 20 kHz) (Direct mode)

Rated output:

Unbalanced RCA pre-output: 1.2 V

Balanced XLR pre-output: 2.4 V

Digital

D/A output:

Rated output — 2 V (at 0 dB playback)

Total harmonic distortion — 0.008 % (1 kHz, at 0 dB)

S/N ratio — 102 dB

Dynamic range — 100 dB

Digital input:

Format — Digital audio interface

Phono equalizer

Input sensitivity:

2.5 mV

RIAA deviation:

±1 dB (20 Hz to 20 kHz)

S/N:

74 dB (IHF-A weighted, with 5 mV input)

Distortion factor:

0.03 % (1 kHz, 3 V)

Video section

Standard video connectors

Input/output level and impedance:

1 Vp-p, 75 Ω/ohms

Frequency response:

5 Hz – 10 MHz — 0, –3 dB

Color component video connector

Input/output level and impedance:

Y signal — 1 Vp-p, 75 Ω/ohms

PB / CB signal — 0.7 Vp-p, 75 Ω/ohms

PR / CR signal — 0.7 Vp-p, 75 Ω/ohms

Frequency response:

5 Hz – 60 MHz — 0, –3 dB

Wireless LAN section

Network type (wireless LAN standard):

Conforming to IEEE 802.11a/b/g/n
(Wi-Fi® compliant) ∗1

Security:

WEP 64 bit, WEP 128 bit

WPA/WPA2-PSK (AES)

WPA/WPA2-PSK (TKIP)

Used frequency range:

2.4 GHz, 5 GHz

The Wi-Fi® CERTIFIED Logo and the Wi-Fi CERTIFIED On-Product Logo are registered trademarks of the Wi-Fi Alliance.

Bluetooth section

Communications system:

Bluetooth Specification Version 3.0 + EDR (Enhanced Data Rate)

Transmission power:

Bluetooth Specification Power Class 1

Maximum communication range:

Approx. 30 m in line of sight ∗2

Used frequency range:

2.4 GHz

Modulation scheme:

FHSS (Frequency-Hopping Spread Spectrum)

Supported profiles:

A2DP (Advanced Audio Distribution Profile) 1.2

AVRCP (Audio Video Remote Control Profile) 1.5

Corresponding codec:

SBC

Transmission range (A2DP):

20 Hz – 20,000 Hz

The actual communication range varies depending on the influence of such factors as obstructions between devices, electromagnetic waves from microwave ovens, static electricity, cordless phones, reception sensitivity, antenna performance, operating system, application software etc.

General

Power supply:

AC 230 V, 50/60 Hz

Power consumption:

90 W

Power consumption in standby modes:

Standby modes

Setting items in the menu

Power consumption

Network Control
link

Allow Update
link

HDMI Pass Through
link /
HDMI Control
link

Normal standby

Off In Standby

Off

Off

0.2 W

Network control (Bluetooth)

Always On

Off

2.9 W

Network control (Ethernet)

Always On

Off

2.9 W

Network control (Wi-Fi)

Always On

Off

3.7 W

CEC standby

Off In Standby

Off

On

0.5 W

RS-232C standby ∗

Off In Standby

Off

Off

0.5 W

When this unit is in standby mode by sending a standby command from the external controller via the RS-232C connector of this unit.

For purposes of improvement, specifications and design are subject to change without notice.

back to top