Search result
Connecting 9.1-channel speakers
This system, which is based on a 5.1-channel system, plays back up to 9.1-channels at the same time.
Up to 11.2-channels can be connected by using either UNBALANCED RCA connectors or BALANCED XLR connectors.
This example explains how to make a connection when using UNBALANCED RCA connectors.
Example connection when using one set of ceiling speakers
![Pict SP Layout 9.1 TM](fig/Pict SP Layout 9.1 TM_DRDZILxbpvkjse.png)
Set “Height” - “Height Sp” to “2ch” in the menu when connecting in this configuration. link
![Conne SP 9.1 TM A74U](fig/Conne SP 9.1 TM A74U_DRDZILipokpsgm.png)
The top front or top rear speakers can be connected instead of the top middle speakers. In this case, set the ceiling speakers to be connected under “Height” - “Layout” in the menu. link
Example connection when using two sets of ceiling speakers
![Pict SP Layout 9.1 TR TF](fig/Pict SP Layout 9.1 TR TF_DRDZILtwllzcou.png)
Set “Floor” - “Layout” to “5ch” or set “5ch & SB” and “Height Sp” to “4ch” in the menu when connecting in this configuration. link
![Conne SP 9.1 TF TR A74U](fig/Conne SP 9.1 TF TR A74U_DRDZILirqcvgax.png)
You can change the combination of the HEIGHT1 and HEIGHT2 channels in the settings. link
Example connection when using one set of height speakers
![Pict SP Layout 9.1 FH](fig/Pict SP Layout 9.1 FH_DRDZILxeeyaemu.png)
Set “Height” - “Height Sp” to “2ch” in the menu when connecting in this configuration. link
![Conne SP 9.1 FH A74U](fig/Conne SP 9.1 FH A74U_DRDZILzqmbvdcq.png)
The rear height speakers can be connected instead of the front height speakers. In this case, set the height speakers to be connected under “Height” - “Layout” in the menu. link
Example connection when using two sets of height speakers
![Pict SP Layout 9.1 RH FH](fig/Pict SP Layout 9.1 RH FH_DRDZILniwbhcbl.png)
Set “Floor” - “Layout” to “5ch” or set “5ch & SB” and “Height Sp” to “4ch” in the menu when connecting in this configuration. link
![Conne SP 9.1 FH RH A74U](fig/Conne SP 9.1 FH RH A74U_DRDZILbiggosyu.png)
You can change the combination of the HEIGHT1 and HEIGHT2 channels in the settings. link
Example connection when using one set of Dolby Atmos Enabled speakers
![Pict SP Layout 9.1 FD](fig/Pict SP Layout 9.1 FD_DRDZILqtibciod.png)
Set “Height” - “Dolby Sp” to “2ch” in the menu when connecting in this configuration. link
![Conne SP 9.1 FD A74U](fig/Conne SP 9.1 FD A74U_DRDZILpfeyzsmt.png)
The surround Dolby or back Dolby speakers can be connected instead of the front Dolby speakers. In this case, set the Dolby Atmos Enabled speakers to be connected under “Height” - “Layout” in the menu. link
Example connection when using two sets of Dolby Atmos Enabled speakers
![Pict SP Layout 9.1 SD FD](fig/Pict SP Layout 9.1 SD FD_DRDZILtuclzbin.png)
![Conne SP 9.1 FD SD A74U](fig/Conne SP 9.1 FD SD A74U_DRDZILecudxybe.png)
You can change the combination of the HEIGHT1 and HEIGHT2 channels in the settings. link
Example connection for the Auro-3D 9.1-channel system
This speaker configuration is optimized for Auro-3D playback.
![Pict SP Layout 9.1 Auro3D](fig/Pict SP Layout 9.1 Auro3D_ZHOBILhxskjiex.png)
![Conne SP 9.1 Auro A74U](fig/Conne SP 9.1 Auro A74U_DRDZILerbfqqbu.png)
You can change the combination of the HEIGHT1 and HEIGHT2 channels in the settings. link
For the best Auro-3D experience Surround Height speakers are recommended, however you may substitute Rear Height speakers from a Dolby Atmos speaker setup in place of Surround Height speakers.